Sunday, February 28, 2010

Stamped and Embossed Pendants

Supplies:
Dominoes - available at Target or many other stores
Sanding blocks ($3.50 for 2; item #103301)
Various stamps - some suggested sets:
"Charming" ($19.95; item #116519),
"Very Thankful" ($14.95; item #115338),
"Jayne's Type Alphabet" ($43.95; item #114401)
Classic Stampin' Pads in various colors ($5.95 each) OR Stampin' Write markers ($31.95 for 12 colors)
Clear Stampin' Emboss powder ($4.75; item #109130)
Heat Tool ($29.95; item #100005)
Simply Adorned chain ($10.95; item #116800)
Extra large glue on bails (necklace holders) - available at The Bead Cache in Fort Collins
E-6000 Glue - available at hardware stores
Optional supplies:
Versamark ink ($7.50; item #102283)
Brayer ($12.50; item #102395)

Step 1 - To prepare your dominoes, sand the shiny coating off the back with a sanding block. Remember to sand the edges and corners as well. Discard any dominoes with flaws or discolorations.

Step 2 - Stamp your favorite image with Classic ink directly on the domino. Or, color directly on the rubber stamp with Stampin' Write markers, "huff" on the stamp to moisten it, and then stamp the domino.

If your image is crooked or smudged, you can wipe it off with a baby wipe and start over. You can also wipe off unwanted parts of an image, like the "thank you" from the peacock. Always wipe off the moisture from the baby wipe, or embossing powder will stick to it.

Step 3 - Before the ink dries (you have 1-2 minutes), spoon a generous amount of clear Stampin' Emboss powder on the stamped image, then tap off the excess. Make sure there is embossing powder over all the stamped image, but none on the background.

Step 4 - Using the heat tool, heat the stamped image until the Stampin' Emboss powder becomes clear and shiny. The embossed layer will not lie perfectly smooth on the domino, but may appear dimpled or wavy. This is normal. Allow the domino to cool.

Step 5 - Repeat steps 2 - 4 to achieve a layered design. When the last layer has cooled, put on a latex glove and stamp your finger on a Stampin' Pad. Rub the ink into the unstamped areas of the domino, working it in around all the embossed areas, to give the domino a background color. You can use your fingers to blend colors or create textures. In one of my domino examples you can see how I created water, trees, and sky just by rubbing in ink.

Step 6 - If your background color dries before you can apply Stampin' Emboss powder, roll on a clear "sticky" ink called Versamark. First roll a brayer on the Versamark pad, then roll the brayer over your domino. Clean the brayer roll with a baby wipe after every use. Adding Versamark ink will allow you to cover the entire domino front with Stampin' Emboss powder.

Step 7 - Once your domino is finished, allow it to cool. Apply a small skim of E-6000 glue to the unstamped side of the domino, and also to the back of the glue-on bail. Allow the glue to sit and get tacky for 2-5 minutes. Then press the bail on to the domino, and allow the glue to harden for 24 hours.

Add a Simply Adorned necklace chain to your stamped pendant, and you're done!

Charly Bratt
CharlysInkLink@gmail.com
http://charlysinklink.blogspot.com
http://www.charlysinklink.stampinup.net/

4 comments:

  1. Just a tip - when stamping on the smooth dominoes, the images can come out blobby and thick if there is too much ink on the stamp. The peacock, in particular, sometimes comes out blobby. Try stamping off your stamp before stamping on the domino. If stamping off takes off too much ink, try stamping off on something smooth like the imaging sheet to a stamp-a-ma-jig. Experiment, you can always rub the ink off the domino and try again.

    ReplyDelete
  2. Hi I would love to make these just one question do you use dominos that you play with the ones with black spots or are they special ones that dont have spots.
    thank you
    megan
    www.megan-finishingtouches.blogspot.com

    ReplyDelete
  3. I use basic dominoes I buy at Target, they have spots on the other side. These actually have multi-colored spots, which are a little less than elegant, but my customers don't seem to mind.

    I haven't tried changing the color of the spots, but you could try embossing down in the holes/spots with white embossing powder, or something like it. You could even try filling the spots with Crystal Effects. I haven't tried that yet, but I was thinking about it.

    ReplyDelete
  4. They turn out fantastically - love it!

    ReplyDelete